• Torque: 2.5 to 5,700 Ounce-Inches
• Sizes: NEMA 08, 11, 14, 15, 17, 23, 24, 34 and 42
• 1.8 and 0.9 Degree, Square-Bodied, High-Torque Stepper Motors
• Up to Four Stack Lengths, Several Windings in Each Frame Size
• Four, Six or Eight Lead Wires, Or Conduit Boxes
• Customization and Motor Adders Available
• Drop-In Replacement for Most Competitors, at Huge Savings!

• Torque: 40 to 1,575 Ounce-Inches
• Sizes: NEMA 23, 34 and 42
• 1.8 Degree, Round-Bodied, "Legacy" Motors
• Up to Three Stack Lengths, Several Windings in Each Frame Size
• Six or Eight Lead Wires, Or Conduit Boxes
• Specials and Motor Adders Available
• Save on Drop-In Replacement of Competitors

• Torque: 1 to 23 Ounce-Inches
• Sizes: 15 to 57mm Diameter
• Cost-Effective, Brushless Stepper Motors
• Customization and Motor Adders Available
• Drop-In Replacement for Most Competitors
• Low Prices, Huge Selection

• Torque: 35 to 5,700 Ounce-Inches
• Sizes: NEMA 17, 23, 34 and 42
• 1.8-Degree, High-Torque Stepper Motors
• Up to Four Stack Lengths, Several Windings in Each Frame Size
• Meets Splash-Proof Requirements
• Made for Harsh or Humid Environments
• Protective Shaft Seal for Longer Life Cycle

• Torque: Up to 4,000 Ounce-Inches
• Sizes: NEMA 11, 17 and 23
• Cost-Effective Stepper Motor with Gearbox
• High-Torque in Compact Package
• Offered in Five Stack Lengths
• Available in 14 Gear Ratios

• Torque: Up to 3,500 Ounce-Inches
• Sizes: NEMA 23 and 34
• Cost-Effective Stepper Motor with Spur Gearbox
• Available Up to 12 Gear Ratios
• Customization is Available

• Torque: 300 to 4000 g-cm of Torque
• Sizes: 24 to 42mm Diameter
• PM Stepper Motor with Integrated Gearbox
• Precise Motion at a Low Cost
• Customization is Available
• 100 Piece Minimum Order Requirement

• Linear Force: 40 to 279 lbs.
• Sizes: NEMA 11, 17, 23 and 34
• Converts Rotary Motion to Linear Motion
• 6 or 12 Inch Lead Screws, with Several Pitches
• Four and Six-Lead Wire Configurations
• Customization Is Available

• Linear Force: 2 to 22.2 lbs.
• Sizes: 20 to 57mm Diameter
• Converts Rotary Motion to Linear Motion
• Simple, Cost-Effective Design
• Four or Six-Lead Wire Configurations
• Customization Is Available

• Linear Force: 2 to 22.2 lbs.
• Sizes: 20 to 42mm Diameter
• Converts Rotary Motion to Linear Motion
• Simple, Cost-Effective Design
• Four or Six-Lead Wire Configurations
• Customization Is Available

• Torque: 31 to 1,700 Ounce-Inches
• Sizes: NEMA 17, 23 and 34
• High-Torque, 1.8 Degree Stepper Motors
• Over-Temperature and Short-Circuit Protection
• Microstep Driver, Resolutions up to 1,600spr
• Cable, Connector or Encoder Adder Options
• Special Windings and Shaft Modifications Available

• Torque: 31 to 425 Ounce-Inches
• Sizes: NEMA 17 and 23
• High-Torque, 1.8 Degree Stepper Motors
• Integrated Driver with Easy-to-Use Controller
• Microstep Driver, Resolutions up to 1,600spr
• Encoder Adder Options
• Special Windings and Shaft Modifications Available
• Easy-to-Use, FREE Software with Purchase

• Driver Type: 110VAC or 220VAC Input
• Current Range: 0.5 to 12.5 Amps
• Bilevel, Microstep and Line-Powered Drivers
• PCB, Modular and Enclosed Packaging Styles
• Offered as One to Four-Axis Units
• Driver, Power Supply in Fan-Cooled Packages

• Driver Type: DC Input
• Current Range: 0.2 to 12.5 Amps
• High-Performance, Bilevel and Microstep
• Also Available are L/R and Legacy Drivers
• PCB, Modular/Enclosed Packaging Styles
• Offered as Single-Axis Units
• Requires DC Power Supply

• Driver Type: Transformer - AC Input
• Current Range: 1.0 to 10.0 Amps
• Bilevel and Microstep Drivers
• PCB, Modular/Enclosed Packaging Styles
• Offered as Single-Axis Units
• Requires Transformer

• Cost-Effective Motion System
• Compatible with Anaheim Automation Drivers
• Command Sets: 18 or 40 Simple Commands
• Can Daisy-Chain to Control up to 99 Axes
• Easy-to-Use, FREE Software with Purchase
• Compact and Rugged Modular Packaging

• Linear Ramping Pulse Generator with Bracket
• Compatible with Anaheim Automation Drivers
• Adjustable Base and Max Speeds
• 2 Speed Ranges, Up to 20,000 pulses/second
• Control of Acceleration and Deceleration

• Perfect for Repetitive Motion Requirements
• Compatible with Anaheim Automation Drivers
• Internal Index Count Switches
• Inputs for External Count Modules
• Pulse Rates up to 14,792 Pulses Per Second
• Index on the Fly Capability

• Driver Type: Drivers/Controllers
• Current Range: 0.5 to 10.0 Amps
• Bilevel and Microstep Drivers
• Modular and Enclosed Packaging Styles
• Single-Axis, Daisy-Chained for Multi-Axes
• Driver, Controller and Power Supply Packages
• Easy-to-Use, FREE Software with Purchase

• Driver Type: Drivers/Pulse Generators
• Current Range: 0.5 to 10.0 Amps
• Bilevel and Microstep Drivers
• PCB, Modular/Enclosed Packaging Styles
• Offered as Single-Axis Units
• Driver, Pulse Generator and Power Supply Packages

• Driver Type: Drivers/ Preset Indexers
• Current Range: 0.5 to 12.5 Amps
• High-Performance, Bilevel and Microstep Drivers
• Offered as One or Two-Axis Units
• Counter Modules Available Separately
• Driver, Indexer and Power Supply Packages

• Torque: 0.7 to 900 Ounce-Inches
• Sizes: Ten sizes from NEMA 09 to 48
• Huge Selection with a Large Stock Base
• Ideal Solution for Velocity Control Applications
• Customization for Voltage, Current and Max Speed
• Round-Bodied, Square Flange and Square-Faced Styles
• Shaft Modifications and Motor Adders Available

• Torque: 0.7 to 900 Ounce-Inches
• Sizes: NEMA 23 and 34
• Meets Splash-proof Requirements
• Ideal for Harsh or Humid Environments
• Protective Shaft Seals for Longer Life Cycles
• Up to Five Stack Lengths, Several Windings
• Customization and Motor Adders Available

• Sizes: NEMA 09, 11, 17 and 23
• Speeds: Less than 500 to 15,000RPM
• Closed-Loop Control for Velocity Applications
• Round-Bodied BLDC Motor/Planetary Gearbox
• Shaft Modifications and Motor Adders Available

• Sizes: NEMA 23 and 34
• Speeds: Less than 225 to 11000 RPM
• Closed-Loop Control for Velocity Applications
• BLDC Motor Integrated with Spur Gearbox
• Shaft Modifications and Motor Adders Available

• Speed: Up to 4,000RPM
• Sizes: NEMA 17, 23, and 34
• DC Brushless Motor with Built-In Speed Controller
• Matched Components Eliminates Selection Errors, Reduces Wiring
• Customization for Voltage, Current, and Max Speed is Available
• Protection Against Over-Current, Hall Sensor Error, and Under-Voltage
• Shaft Modifications and Motor Adders Are Available
•  

Brushless Drivers/Control

• Input Ranges: 6 to 50VDC
• Max Power: 24 to 250 Watts
• Peak Current: 3 to 10Amps
• Low-Cost Speed Controllers
• Covers a Wide Range of Motors
• Printed Circuit Board Style
• Overcurrent and Undervoltage Protection

• Input Ranges: 10 to 50VDC or 85 to 135VAC
• Max Power: 36 to 500 Watts
• Peak Current: 3 to 60Amps
• Low-Cost Speed Controllers
• Covers a Wide Range of Motors
• Huge Selection, Six Different Series Offered
• Printed Circuit Board and Enclosed Styles
• Over-Current and Under-Voltage Protection

• Input Ranges: 20 to 50VDC, or 85 to 135VAC
• Max Power: 750 to 1,500 Watts
• Peak Current: 15 to 60Amps
• Low-Cost Speed Controllers
• Covers a Wide Range of Motors
• Three Different Series Offered
• Enclosed Styles
• Over-Current and Under-Voltage Protection

• Sizes: NEMA 23, 34 and 42
• Gear Ratios: Up to 33 Ratios from 3:1 to 1,000:1
• Backlash: As Low as 7 Arc-Min for Precision Series
• Torque Up To 167,808 Ounce-Inches
• Precision Clamping System
• Compatible with Most Servo, Stepper, AC or DC Motors
• Maintenance-Free, Lifetime Lubrication

• Sizes: NEMA 17, 23, 34, and 42
• Gear Ratios: From 3:1 to 512:1
• Backlash: As low as 8 Arc-Min
• Torque Up To 113,280 Ounce-Inches
• Precision Clamping System
• Compatible with Most Servo, Stepper, AC or DC Motors
• Maintenance-Free, Lifetime Lubrication

• Sizes: NEMA 17, 23, 34 and 42
• Gear Ratios: 22 Ratios from 3:1 to 512:1
• Backlash: As low as 5 Arc-Min
• Torque Up To 36,816 Ounce-Inches
• Right Angle Ideal for Redirecting Power Flow
• Maintenance-Free, Lifetime Lubrication
• Compatible with Most Servo, Stepper, AC or DC Motors

• Sizes: NEMA 23, 34 and 42
• Gear Ratios: Ratios from 3:1 to 64:1
• Backlash: As Low as 16 Arc-Min
• Life: 30,000 Hours Design Life
• Torque Up To 36,816 Ounce-Inches
• Patented Precision Clamping System
• High Durability, 96% Efficiency
• Maintenance-Free, Lifetime Lubrication

• Sizes: 60mm, 70mm, 80mm, and 90mm
• Gear Ratios: Up to 20 Ratios from 3.6:1 to 1800:1
• Torque Up To 2,777 Ounce-Inches
• To be mated with ACP-MxI AC Induction Motors 
• Cost-Effective Solution 
• Strengthened Gearhead option for select models 

• Rated Torque: 91 to 338 Ounce-Inches
• Rated Speed: 3,000 RPM
• Flange Sizes: 60-80mm
• Industrial-Grade Intelligent Power Modules
• IP65 Sealed Motors
• High Overload and Disturbance Rejection
• System Includes Power Cable, Encoder Cable, and Communication Cable

• Rated Torque: 91 to 5,438 Ounce-Inches
• Rated Speed: 1,000 to 3,000 RPM
• Flange Sizes: 60-180mm
• Industrial-Grade Intelligent Power Modules
• IP65 Sealed Motors
• High Overload and Disturbance Rejection
• System Includes Power Cable, Encoder Cable, and Communication Cable

• Rated Power: 200-1,000 Watts
• Rated Torque: 91-450 oz-in
• Rated Speed: 3,000 RPM
• Rated Current: 1.3-5.3 Arms
• Flange Size: 60-130mm
• IP65 Sealed
• 2,500 PPR Incremental Encoder
• Medium Inertia to Maximum Torque
• Brakes and Shaft Options Available

• Rated Power: 1,000-5000 Watts
• Rated Torque: 677-3,385 oz-in
• Rated Speed: 2,000 RPM
• Rated Current: 6.0-28.0 Arms
• Flange Size: 130-180mm
• IP65 Sealed
• 2,500 PPR Incremental Encoder
• Medium Inertia to Maximum Torque
• Brakes and Shaft Options Available

• Rated Power: 1,000-4,000 Watts
• Rated Torque: 1,352-5,438 oz-in
• Rated Speed: 1,000 RPM
• Rated Current: 6.0-24.0 Arms
• Flange Sizes: 130-180mm
• IP65 Sealed
• 2,500 PPR Incremental Encoder
• Medium Inertia to Maximize Torque
• Brakes and Shaft Options Available

• Power Rating: 200 to 750 Watts
• Drive Control: Position and Speed
• Communication: CANopen and MODBUS
• Communication Interface: RS232
• High-Speed, High-Precision Servo Drives
• ESView Communication Software
• 4 Input Channels, 4 Output Channels
• Industrial-Grade Intelligent Power Modules
• High Overload and Disturbance Rejection
• Modbus for Networking up to 15 Motors
• Optional Handheld Controller

• Power Rating: 2,000 to 3,000 Watts
• Drive Control: Position, Speed, Torque
• Communication: CANopen and MODBUS
• Communication Interface: RS232
• High-Speed, High-Precision Servo Drives
• ESView Communication Software
• Industrial-Grade Intelligent Power Modules
• High Overload and Disturbance Rejection
• Modbus for Networking up to 32 Motors
• Built-in Panel Operator

• Power Rating: 200 to 5,000 Watts
• Drive Control: Position, Speed, Torque
• Communication: CANopen and MODBUS
• Communication Interface: RS485
• High-Speed, High-Precision Servo Drives
• ESView Communication Software
• Analog Input Reference for Speed and Torque
• 8 Input Channels, 4 Output Channels
• Industrial-Grade Intelligent Power Modules
• High Overload and Disturbance Rejection
• Modbus for Networking up to 32 Motors
• Built-in Panel Operator

• Up to 224N of Peak Force
• Up to 1,920 Watts
• Overlapping Windings for Shorter Overall Length
• Superior Thermal Efficiency
• Features I Beam design

• Up to 606N of Peak Force
• Up to 1,814 Watts
• Overlapping Windings for Shorter Overall Length
• Superior Thermal Efficiency
• Features I Beam design

• Up to 1,048N of Peak Force
• Up to 4,147 Watts
• Overlapping Windings for Shorter Overall Length
• Superior Thermal Efficiency
• Features I Beam design

• Up to 3,558N of Peak Force
• Up to 9,677 Watts
• Overlapping Windings for Shorter Overall Length
• Superior Thermal Efficiency
• Features I Beam design

• EMJ, EMG, and EML Servo Encoder Cables
• EMJ, EMG, and EML Servo Motor Power Cables
• EDC and PRONET-E Communication Cables
• EDC Handheld Controller
• PRONET-E 50-Pin Breakout Board
• Custom Lengths Available

• Save up to 50% over competing brands
• Ground and Precision Rolled Ball Screws
• Delivery in 4 weeks
• Ball Screw Diameters Rangning From
  4mm to 80mm
• High Precision from C0 to C10 Grade

• Flange Type Nuts
• Ball Screw Diameters Ranging From
  6mm to 50mm
• Solid and Hollow Spline Shaft Options
• Normal, High, and Precision Grade Accuracy
• Zero Preload, Slight Preload, and Medium Preload Options

• Cylindrical Type Nuts
• Ball Screw Diameters Ranging From
  6mm to 50mm
• Solid and Hollow Spline Shaft Options
• Normal, High, and Precision Grade Accuracy
• Zero Preload, Slight Preload, and Medium Preload Options

• Size: 7mm to 65mm Linear Guide Rail
• Dynamic Load: 1.41 to 273.6kN
• Static Load: 2.00 to 419.04kN
• Rail Lengths from 100 to 4,000mm in Stock
• Custom Rail Sizes Available
• Standard and Wide Matched Bearing Blocks
• End-Seal Options: Standard or Reinforced
• Pre-Load Classes: Standard, Light, or Medium

• Size: 3mm to 45mm Linear Guide Rail
• Dynamic Load: 0.19 to 89.5kN
• Static Load: .31 to 169.1kN
• Rail Lengths from 200 to 4,000mm in Stock
• Custom Rail Sizes Available
• Standard and Wide Matched Bearing Blocks
• End-Seal Options: Standard or Reinforced
• Pre-Load Classes: Standard, Light or Medium

• Size: 15 mm to 65 mm Linear Guide Rail
• Dynamic Load: 10.3 to 288kN
• Static Load: 27.5 to 756kN
• Rail Lengths from 100 to 3,500mm in Stock
• Interchangeable Blocks and Rails
• Custom Rail Sizes Available
• Standard and Wide Matched Bearing Blocks
• End-Seal Options: NSK K1 Lubrication Unit, Double Seal, and Rail Cover
• Pre-Load Classes: Slight or Medium

•  
• Fixed-Side and Supported-Side Options
• Rectangular and Round Types
• Ball Screw Diameters Ranging from 10mm to 50mm
• Acceptable Input Shaft Diameters Ranging from 6mm to 40mm
• Black Oxide Surface Treatment

•  
•  
• Miniature Linear Guide Stoppers
• Sizes Available: 7mm to 15mm
• Compatible with Standard and Wide Rails
• Stoppers and Screws made of Stainless Steel Material

•  
•  
• 3 Different Size Nozzle Adaptors
• Compatible Linear Guides:
  • CPC-MR12 and CPC-MR15
  • CPC-ARC15 to CPC-ARC45
  • CPC-HRC15 to CPC-HRC45
• Easier Lubrication Process
• Grease Gun Sold Separately

• Type: ACME Screw
• Travel Options: 0.4 - 18 Inches
• Accuracy: 0.003 in/ft
• Speed: Up to 12 in/s (305 mm/s)
• Zero Backlash
• Heavy Duty Applications, Up to 8,000 lbs
• Supported Rails, Low-Profile Design. Motor, Encoder, and Cable Options

• Type: Ball Screw
• Travel Options: 100 - 1,240mm
• Accuracy: 20µm/mm
• Speed: Up to 1,500 mm/s
• Backlash: .005mm
• Dynamic Loads up to 6699 lbs
• Motor, Encoder, and Cable Options. Build Part Number to your Requirements

• Type: Ball Screw
• Travel Options: 100 - 2,000mm
• Accuracy: Up to 50μm/mm
• Speed: Up to 1,673 mm/s
• Backlash: 0.02-0.005mm
• Heavy Duty Applications, Up to 200kg (441lbs)
• Optional Kits: Limit Sensors, Motor Mounting Kits, Square Nuts, and Module Mounting Plates. Fully Enclosed Aluminum Casing and Belt

•  
•  
• X-Axis Stoke Length: 250-2,000mm
• Y-Axis Stroke Length: 100-1,000mm
• Backlash: .02-.005mm
• Transportable Mass: Up to 40kg
• Fully covered aluminum casing with belts to elimnate contaminates
• Optional Limit Sensor Kits, Motor Mounting Kits, and Home Positioning Sensor Kits

• Voltage: 110, 220 or 380VAC
• Torque: 5.38 to 600 Ounce-Inches
• Speed: Up to 1800RPM
• Metric Frame Sizes: 60mm to 100mm
• IEC Frame Sizes: 63, 71, and 80
• Round-Bodied with Square Mounting Flange
• Totally Enclosed Fan Cooled (TEFC)
• Self Starting and Reversible
• Huge Selection, Low-Cost AC Induction Motors. Customization for Specific Requirements Available. Shaft Modifications and Motor Adders Available

• Voltage: 110 or 220VAC
• Torque: 42 to 1,699 Ounce-Inches
• Speed: Up to 1800RPM
• Frame Sizes: From 2.3 to 6.14 Inches Across Flange
• Low-Cost AC Synchronous Motors
• Round-Bodied with Square Mounting Flange
• Comes with Matching Capacitor and Resistor
• Customization for Specific Requirements Available
• Shaft Modifications and Motor Adders Available

• Torque: 16 to 5,664 Ounce-Inches
• Sizes: 60mm to 100mm
• Low-Cost AC Motors with Spur Gearboxes
• Round-Bodied with Square Mounting Flange
• Customization for Specific Requirements Available
• Shaft Modifications and Motor Adders Available
• Reversible

• Torque: Up to 56 Ounce-Inches at 30rpm
• Sizes: 44mm and 50mm
• Low-Cost AC Synchronous Gearmotors
• Round-bodied with Square Mounting Flange
• Frequently Used in Appliances, Displays, Printers, Timers, Pumps, etc.
• Customization for Optimizing Current, Voltage, Torque and Max Speed
• Shaft Modifications and Motor Adders Available

• Torque: 708 oz-in to 27,614 oz-in
• Power: 200Watts to 750Watts
• Gear Ratios from 5:1 to 200:1
• Shaft Diameters from 18mm to 40mm
• Foot and Flange-Mount Options Available
• Low-Cost AC Industrial Gearmotors
• Compact Size, High Efficiency
• IP55 Protection
• Class F Insulation

• Input Range: 110VAC or 220VAC
• Max Power: 6 to 600 Watts
• Closed Loop Operation Available
• RPM Display Available
• Simple, Cost-Effective Design
• Small Package Designs
• Covers a Wide Range of Motor Applications
• Customization is Available

• Input Range: 115, 230, or 460VAC
• Max Power: 0.25 - 5.0 Horsepower
• High-Quality and Cost-Effective Solution for Your Three-Phase AC Motor
• Over Current and Voltage Stall Prevention, Current Detection, Full Overload Protection, Motor Overheat Protection, and Reset after Fault
• Space-Saving and Compact Design for Easy DIN Rail Mounting. Side-by-Side Installation to Save Space
• Standard MODBUS Protocol via RS-485
• PROFIBUS, DeviceNet, LonWorks, and CANopen Compatible

• Input Range: 230 or 460VAC
• Max Power: 1 to 536 Horsepower
• Open-Loop Speed Control
• Detachable LCD Keypad Offers a User-Friendly Operation Interface
• Advanced Network Functions Built-In: RS485, BACnet and MODBUS
• Modular Design for Flexible Extension and Ease-of-Maintenance
• Greatly Improve Efficiency of Variable Torque and Constant Horsepower Load Applications
• Excellent for Fan and Pump Applications

• RS-485 to USB Data Converter
• Supports Baud Rate from 75 to 115.2kbps
• No External Power Supply Required
• Conduit Boxes

• 65536 True Color TFT LCD
• 32-bit 400, 520, 624 or 800 MHz RISC CPU
• 8M FLASH ROM and 16M SDRAM
• 256KB Recipe Memory
• Powerful Timer Function
• Supports Simultaneous Communication of Multiple Serial Ports

• High Performance 32-Bit, 520 MHz CPU
• Minimum Cycle Time of 0.1ms
• CANopen 2.0 Communication
• Supports Remote Downloading/Monitoring/    Debugging
• 2 CAN Ports, 2 Serial Ports, 1 Ethernet Port
• 2MB Program Memory
• Photoelectric Isolation I/O

• Bluetooth I/O Module
• 8 Inputs/8 Outputs
• Analog/Digital/Interrupt Inputs
• Timer Interrupts
• Configure Inputs as Pull Ups or Pull Downs
• Store 2KB of Program Memory
• Run Several Routines

• USB I/O Module
• 8 Inputs/8 Outputs
• Analog/Digital/Interrupt Inputs
• Timer Interrupts
• Configure Inputs as Pull Ups or Pull Downs
• Store 2KB of Program Memory
• Run Several Routines

• Voltage: 1.2 - 230VDC
• Rated Torque: 0.08 to 113.28 Ounce-Inches
• Frame Sizes: 20mm to 95mm
• Speed: 900 to 26,100 RPM
• Cost-Effective Rotary Motion Control
• DC Motors are Fully Reversible
• Pump, Fan, and Drill Applications
• Popular for Robotics and Hobbyists
• Customization and Motor Adders Available
• Designed for High-Volume Applications (Many Items in Stock)

• Voltage: 90VDC
• Horsepower: 1/27 and 1/8
• Rated Torque: 20.8 to 70 Ounce-Inches
• Frame Sizes: 66mm to 80mm
• Speed: 1800 RPM
• Cost-Effective Rotary Motion Control
• DC Motors are Fully Reversible
• Totally Enclosed Non Ventilated (TENV)
• Double Shielded Ball Bearings

• Voltage: 90 - 180VDC
• Horsepower: 1/2, 3/4, and 1HP
• Rated Torque: 288 to 576 Ounce-Inches
• Frame Size: 56C
• Speed: 1,800 and 2,500 RPM
• Cost-Effective Rotary Motion Control
• DC Motors are Fully Reversible
• Totally Enclosed Fan Cooled (TEFC)
• Class F Insulation Means Max Temp up to 
   221° F at Full Load

• Input Voltage: 12-24VDC
• Sizes: From 22mm to 60mm
• Continuous Torque: Up to 4,166 oz-in
• Speed: Up to 1,350 RPM
• Gear Ratios Ranging from 3.6:1 to 720:1
• Custom Versions are Available

• Input Voltage: 24-90VDC
• Sizes: From 66mm to 90mm
• Continuous Torque: Up to 4,800 oz-in
• Speed: Up to 1,000 RPM
• Gear Ratios Ranging from 5:1 to 200:1
• Custom Versions are Available

• Input Voltage: 6-24VDC
• Sizes: From 24mm to 83mm
• Continuous Torque: Up to 2,750 oz-in
• Speed: Up to 1,000 RPM
• Gear Ratios Ranging from 3:1 to 3000:1
• Custom Versions are Available

• Input Voltage: 12-90VDC
• Sizes: From 48mm to 95mm
• Continuous Torque: Up to 1,504 oz-in
• Speed: Up to 360 RPM
• Gear Ratios Ranging up to 81:1
• Custom Versions are Available

• Low-Cost Speed Controller
• Printed Circuit Board Style
• Screw-Type Terminal Blocks for Easy Installation
• Compatible with DC Brush Motors up to 10A Peak and 50V
• Additionally an External Voltage Can Be Used To Control Speed
• Short-Circuit and Over-Current Limiting Protection
• Over-Voltage Protection

• Single-Ended or Differential Outputs for ABI Channels
• Low-Cost; Compact Rugged Housing
• 32 to 5,000 Cycles Per Revolution (CPR)
• 128 to 20,000 Pulses Per Revolution (PPR)
• Optional Third and Fouth Index Channel
• Tracks 0 to 100,000 Cycles Per Second
• Compatible with .059" to 1.00" Bore Size Diameters
• Operating Temperature of -40 to +100°C
• Powered From a Single +5VDC Power Supply
• 2-Channel Quadrature Squarewave Outputs
• Allows for ± .010" Axial Shaft Play

• Single-Ended or Differential Outputs for ABI Channels
• U/V/W Commutation Outputs
  (Differential or Open-Collector)
• 100 to 2,560 Cycles Per Revolution (CPR)
• 400 to 10,240 Pulses Per Revolution (PPR)
• Tracks 0 to 200,000 Cycles Per Second
• Optional Third and Fourth Index Channel
• Compatible with .125" to 1.125" Bore Size Diameters
• Operating Temperature of -40 to +100°C
• Powered From a Single +5VDC Power Supply
• 2-Channel Quadrature Squarewave Outputs
• Allows for ± .005" Axial Shaft Play

• Optical and Magnetic Type
• Single-Ended or Differential Outputs for ABI Channels
• U/V/W Commutation Outputs 
  (Differential or Open-Collector)
• 2 to 10,000 Cycles Per Revolution (CPR)
• 8 to 40,000 Pulses Per Revolution (PPR)
• Optional Third and Fourth Index Channel
• Compatible with .197" to 1.73" Bore Size Diameters
• Powered From a Single +5VDC, +5-30VDC, or +10-30VDC Power Supply
• Operating Temperature of -20° to +105° C
• Allows for ± .005" Axial Shaft Play

• Resolutions: 5, 10, 25, and 50µm
• Linear Travel Speed: Up to 16.0m/s
• Gap Clearance up to 2mm
• Hi-Flex Sensor Cable
• Status LED for Clearance and Speed Error
• Quadrature Squarewave Output
• Push-Pull or Line Driver Circuit Output
• Optional Index Channel
• Operating Temperature -25°C to +85°C
• IP67 Protection Rating
• Up to 50m in Cable Length

• Reference Pole Marker
• Wipers for ENC-LKE51 Series

• Bore sizes from .059" to 1.00"
• Suitable for Optical Encoders
• Applicapable Series:
  • ENC-A2
  • ENC-A3
  • ENC-A4P
  • ENC-A5
  • ENC-EC35