Asahi Enterprise Control system products
Asahi Hyper Regulator 640A / 640B Series
Hyper regulator
640A / 640B series
High-precision type for positive pressure and secondary pressure control
The supply pressure (primary pressure) is reduced and the output pressure (secondary pressure) is controlled to be constant. The built-in controller compensates for output pressure drift.
There are A type with built-in sensor and B type with sensor exterior.
In addition to the pressure sensor, the B type can be connected to analog output sensors such as flow rate sensors and position sensors
Standard specifications
|
Asahi Model number
|
Asahi Hyper Regulator 640AA1
|
Asahi Hyper Regulator 640AB1
|
Asahi Hyper Regulator 640AD1
|
Asahi Hyper Regulator 640AH1
|
|
Set pressure
|
0 ~ 0.8 MPa
|
0 ~ 0.3 MPa
|
0 ~ 0.1 MPa
|
0 ~ 1 MPa
|
|
Input signal * 1
|
0-5V (0-10V / 4-20mA / other, please specify)
|
|
Supply pressure
|
Maximum output span + 0.05MPa
|
|
Power supply
|
24 VDC
|
|
Connection diameter
|
1/8 (1/4 = change the 3rd digit of the model number to 1)
|
|
Fluid used
|
Air (When using a flow rate other than air, select the external pilot type)
|
|
Sensor * 2
|
Built-in pressure sensor (A type is changed to B for pressure sensor exterior type)
|
|
Input impedance
|
10 kΩ or more (voltage input) / 300 Ω or less (current input)
|
|
Mounting direction
|
Optional (no drift will occur depending on the mounting direction)
|
|
control method
|
Force balance + APID control
|
|
Flow rate consumed
|
1.5LPM or less (standard type) to 5LPM or less (high speed type)
|
|
weight
|
0.8 kg
|
|
Insulation resistance
|
1 MΩ or more
|
|
Hysteresis
|
± 0.05% or less
|
|
Linearity
|
± 0.3% or less (depending on the sensor used together)
|
|
Orifice diameter
|
4 mmΦ
|
|
response speed
|
0.05sec or less (Characteristic without load)
|
|
Material
|
Body = ADC12 / Internal parts = A2017, SUS304
diaphragm = NBR or Viton / Seal = Viton
|
NOTE
* 1 - Change the last digit of the model number.
(1 = 0-5V / 2 = 0-10V / 3 = 4-20mA / 5 = Other, please specify)
* 2 - By selecting B type, you can bypass the piping resistance and achieve high-speed response. When using an analog sensor other than the pressure sensor, specify the sensor output.
* If compound pressure is required, please refer to 640AC, 640BC
* Please contact us for detailed dimensions and characteristic data.
Asahi Hyper Regulator 640AC, 640BC Series
Hyper regulator
640AC, 640BC series
High precision type for vacuum coupled secondary pressure control
The supply pressure (primary pressure) is reduced and the output pressure (secondary pressure) is controlled to be constant. The built-in controller compensates for output pressure drift.
There are A type with built-in sensor and B type with sensor exterior.
In addition to the pressure sensor, the B type can be connected to analog output sensors such as flow rate sensors and position sensors.
The vacuum type is a 2-way valve. If you need an exhaust port, please use continuous molding.
Standard specifications
|
Asahi Model number
|
Asahi Hyper Regulator 640AC1
|
Asahi Hyper Regulator 640BC
|
|
Set pressure
|
-0.1 ~ 0.3 MPa
|
-0.1 ~ 0.3 MPa
|
|
Input signal * 1
|
0-5V (0-10V / 4-20mA / other, please specify)
|
|
Supply pressure
|
Maximum output span + 0.05MPa
|
|
Power supply
|
24 VDC
|
|
Connection diameter
|
1/8 (1/4 = change the 3rd digit of the model number to 1)
|
|
Fluid used
|
Air (External pilot type is required for vacuum)
|
|
Sensor * 2
|
Pressure sensor built-in type (A type is changed to B for pressure sensor exterior type)
|
|
Input impedance
|
10 kΩ or more (voltage input) / 300 Ω or less (current input)
|
|
Mounting direction
|
Arbitrary (Drift of ± 1% or less occurs depending on the mounting direction)
|
|
control method
|
Force balance + APID control
|
|
Flow rate consumed
|
1.5LPM or less (standard type) to 5LPM or less (high speed type)
|
|
weight
|
0.8kg (continuous molding = 1.4kg)
|
|
Insulation resistance
|
1 MΩ or more
|
|
Hysteresis
|
± 0.1% or less
|
|
Linearity
|
± 0.3% or less (depending on the sensor used together)
|
|
Orifice diameter
|
4 mmΦ
|
|
response speed
|
0.05sec or less (Characteristic without load)
|
|
Material
|
Body = ADC12 / Diaphragm = NBR / Seal = NBR
|
NOTE
* 1 - Change the last digit of the model number.
(1 = 0-5V / 2 = 0-10V / 3 = 4-20mA / 5 = Other, please specify)
* 2 - By selecting B type, you can bypass the piping resistance and achieve high-speed response. When using an analog sensor other than the pressure sensor, specify the sensor output.
* Please contact us for detailed dimensions and characteristic data.
Asahi Hyper regulator 752A, 752B series
Hyper regulator
752A, 752B series
High-precision type for positive pressure and secondary pressure control
The supply pressure (primary pressure) is reduced and the output pressure (secondary pressure) is controlled to be constant. The built-in controller fully compensates for output pressure drift.
There are A type with built-in sensor and B type with sensor exterior.
In addition to pressure sensor, B type can be connected with analog output sensors such as flow rate sensor and position sensor.
Standard specifications
|
Asahi Model number
|
Asahi Hyper regulator 752AA1
|
Asahi Hyper regulator 752AB1
|
Asahi Hyper regulator 752AD1
|
Asahi Hyper regulator 752AH1
|
|
Set pressure
|
0 ~ 1 MPa
|
0 ~ 0.3 MPa
|
0 ~ 0.1 MPa
|
0 ~ 2 (2.5) MPa
|
|
Input signal * 1
|
0-5V (0-10V / 4-20mA / other, please specify)
|
|
Supply pressure
|
Maximum output + 0.1MPa
|
|
Power supply
|
24 VDC
|
|
Connection diameter
|
3/8
|
|
Fluid used
|
Air (When using a flow rate other than air, select the external pilot type)
|
|
Sensor * 2
|
Pressure sensor built-in type (A type is changed to B for pressure sensor exterior type)
|
|
Input impedance
|
10 kΩ or more (voltage input) / 300 Ω or less (current input)
|
|
Mounting direction
|
Arbitrary (Drift of ± 1% or less occurs depending on the mounting direction)
|
|
control method
|
Force balance + APID control
|
|
Flow rate consumed
|
1.5LPM or less (low consumption flow type) to 5LPM or less (standard type)
|
|
weight
|
1.8 kg
|
|
Insulation resistance
|
1 MΩ or more
|
|
Hysteresis
|
± 0.1% or less
|
|
Linearity
|
± 0.5% or less (depending on the sensor used together)
|
|
Orifice diameter
|
11 mmΦ
|
|
response speed
|
0.05sec or less (Characteristic under no load)
|
|
Material
|
Body = A2017 (ADC12)
Diaphragm = Viton, NBR / Seal = Viton
|
NOTE
* 1 Change the last digit of the model number.
(1 = 0-5V / 2 = 0-10V / 3 = 4-20mA / 5 = Other, please specify)
* 2 By selecting B type, the piping resistance can be bypassed and high-speed response can be achieved. When using an analog sensor other than the pressure sensor, specify the sensor output.
* Please refer to 752AC and 752BC when compound pressure is required.
* Please contact us for detailed dimensions and characteristic data.
option
-
CCLINK compatible: Contact us for details.
-
External pilot specification: Use when using a gas other than air.
-
Special diaphragm: Viton and Teflon are available.
-
Special seals: Viton, Teflon and polyurethane are available.
-
High-speed type: Pilot booster is also used. The highest speed control is possible.
* Please contact us for details of optional specifications.
Asahi Hyper regulator 752AC, 752BC series
Hyper regulator
752A, 752B series
High-precision type for positive pressure and secondary pressure control
The supply pressure (primary pressure) is reduced and the output pressure (secondary pressure) is controlled to be constant. The built-in controller fully compensates for output pressure drift.
There are A type with built-in sensor and B type with sensor exterior.
In addition to pressure sensor, B type can be connected with analog output sensors such as flow rate sensor and position sensor.
Standard specifications
|
Asahi Model number
|
Hyper regulator 752AA1
|
Hyper regulator 752AB1
|
Hyper regulator 752AD1
|
Hyper regulator 752AH1
|
|
Set pressure
|
0 ~ 1 MPa
|
0 ~ 0.3 MPa
|
0 ~ 0.1 MPa
|
0 ~ 2 (2.5) MPa
|
|
Input signal * 1
|
0-5V (0-10V / 4-20mA / other, please specify)
|
|
Supply pressure
|
Maximum output + 0.1MPa
|
|
Power supply
|
24 VDC
|
|
Connection diameter
|
3/8
|
|
Fluid used
|
Air (When using a flow rate other than air, select the external pilot type)
|
|
Sensor * 2
|
Pressure sensor built-in type (A type is changed to B for pressure sensor exterior type)
|
|
Input impedance
|
10 kΩ or more (voltage input) / 300 Ω or less (current input)
|
|
Mounting direction
|
Arbitrary (Drift of ± 1% or less occurs depending on the mounting direction)
|
|
control method
|
Force balance + APID control
|
|
Flow rate consumed
|
1.5LPM or less (low consumption flow type) to 5LPM or less (standard type)
|
|
weight
|
1.8 kg
|
|
Insulation resistance
|
1 MΩ or more
|
|
Hysteresis
|
± 0.1% or less
|
|
Linearity
|
± 0.5% or less (depending on the sensor used together)
|
|
Orifice diameter
|
11 mmΦ
|
|
response speed
|
0.05sec or less (Characteristic under no load)
|
|
Material
|
Body = A2017 (ADC12)
Diaphragm = Viton, NBR / Seal = Viton
|
NOTE
* 1 Change the last digit of the model number.
(1 = 0-5V / 2 = 0-10V / 3 = 4-20mA / 5 = Other, please specify)
* 2 By selecting B type, the piping resistance can be bypassed and high-speed response can be achieved. When using an analog sensor other than the pressure sensor, specify the sensor output.
* Please refer to 752AC and 752BC when compound pressure is required.
* Please contact us for detailed dimensions and characteristic data.
option
-
CCLINK compatible: Contact us for details.
-
External pilot specification: Use when using a gas other than air.
-
Special diaphragm: Viton and Teflon are available.
-
Special seals: Viton, Teflon and polyurethane are available.
-
High-speed type: Pilot booster is also used. The highest speed control is possible.
* Please contact us for details of optional specifications.
Asahi Hyper relief valve 635B series
Hyper-relief valve
635B series
High-precision type for positive pressure relief control
By adjusting the displacement of the primary pressure, the process pressure (primary pressure) is controlled to be constant. The integrated controller compensates for process pressure drift.
There is only B type of sensor exterior.
In addition to the pressure sensor, the B type can be connected to analog output sensors such as flow rate sensors and position sensors.
Standard specifications
|
Asahi Model number
|
Asahi Hyper relief valve 635BA1
|
Asahi Hyper relief valve 635BB1
|
Asahi Hyper relief valve 635BD1
|
Asahi Hyper relief valve 635BH1
|
|
Set pressure
|
0 ~ 0.8 MPa
|
0 ~ 0.3 MPa
|
0 ~ 0.1 MPa
|
0 ~ 1 MPa
|
|
Input signal * 1
|
0-5V (0-10V / 4-20mA / other, please specify)
|
|
Supply pressure
|
Unnecessary
|
|
Power supply
|
24 VDC
|
|
Connection diameter
|
1/8 (1/4 = change the 3rd digit of the model number to 6)
|
|
Fluid used
|
Air (Relief pressure control is external pilot type)
|
|
Sensor * 2
|
Pressure sensor exterior type
|
|
Input impedance
|
10 kΩ or more (voltage input) / 300 Ω or less (current input)
|
|
Mounting direction
|
Optional (no drift will occur depending on the mounting direction)
|
|
control method
|
Force balance + APID control
|
|
Flow rate consumed
|
1.5LPM or less (standard type) to 5LPM or less (high speed type)
|
|
weight
|
0.8 kg
|
|
Insulation resistance
|
1 MΩ or more
|
|
Hysteresis
|
± 0.05% or less
|
|
Linearity
|
± 0.3% or less (depending on the sensor used together)
|
|
Orifice diameter
|
4 mmΦ
|
|
response speed
|
0.05sec or less (Characteristic without load)
|
|
Material
|
Body = ADC12 / Diaphragm = NBR / Seal = NBR
|
NOTE
* 1 Change the last digit of the model number.
(1 = 0-5V / 2 = 0-10V / 3 = 4-20mA / 5 = Other, please specify)
* 2 Type B can bypass the piping resistance and achieve high-speed response. When using an analog sensor other than the pressure sensor, specify the sensor output.
* A back pressure proportional to the flow rate is generated due to the internal resistance of the valve. The process pressure cannot be reduced below this back pressure. Please request if you need the data.
* Please contact us for detailed dimensions and characteristic data.
Asahi Hyper relief valve 735B series
Hyper-relief valve
735B series
High-precision type for positive pressure relief control
By adjusting the displacement of the primary pressure, the process pressure (primary pressure) is controlled to be constant. The integrated controller compensates for process pressure drift.
There is only B type of sensor exterior.
In addition to the pressure sensor, the B type can be connected to analog output sensors such as flow rate sensors and position sensors.
Standard specifications
|
Asahi Model number
|
Asahi Hyper relief valve 735BA1
|
Asahi Hyper relief valve 735BB1
|
Asahi Hyper relief valve 735BD1
|
Asahi Hyper relief va lve735BH1
|
|
Set pressure
|
0 ~ 1 MPa
|
0 ~ 0.3 MPa
|
0 ~ 0.1 MPa
|
0 ~ 2 MPa
|
|
Input signal * 1
|
0-5V (0-10V / 4-20mA / other, please specify)
|
|
Supply pressure
|
Not required (external pilot pressure required)
|
|
Power supply
|
24 VDC
|
|
Connection diameter
|
3/8
|
|
Fluid used
|
Air (Relief pressure control is external pilot type)
|
|
Sensor * 2
|
Pressure sensor exterior type
|
|
Input impedance
|
10 kΩ or more (voltage input) / 300 Ω or less (current input)
|
|
Mounting direction
|
Optional (no drift will occur depending on the mounting direction)
|
|
control method
|
Force balance + APID control
|
|
Flow rate consumed
|
1.5LPM or less (standard type) to 5LPM or less (high speed type)
|
|
weight
|
1.8 kg
|
|
Insulation resistance
|
1 MΩ or more
|
|
Hysteresis
|
± 0.05% or less
|
|
Linearity
|
± 0.3% or less (depending on the sensor used together)
|
|
Orifice diameter
|
11 mmΦ
|
|
response speed
|
0.05sec or less (Characteristic without load)
|
|
Material
|
Body = ADC12 / Diaphragm = NBR / Seal = NBR
|
NOTE
* 1 Change the last digit of the model number.
(1 = 0-5V / 2 = 0-10V / 3 = 4-20mA / 5 = Other, please specify)
* 2 The N type can bypass the piping resistance and achieve high-speed response. When using an analog sensor other than the pressure sensor, specify the sensor output.
* A back pressure proportional to the flow rate is generated due to the internal resistance of the valve. The process pressure cannot be reduced below this back pressure. Please request if you need the data.
* Please contact us for detailed dimensions and characteristic data.
Asahi HL regulator 940B series
HL Regulator
940B series
High precision type
The 940B series is a 2-port relief type flow control valve. It can be used to control fluid flow rate, primary pressure, secondary pressure, etc.
The wetted part is SUS316, and only one diaphragm can move in the wetted part.
Compatible with fluids with maximum operating pressure of 1MPa and maximum operating temperature of 150 ℃ or less. It is very useful for controlling special fluids under conditions that cannot be used with hyper regulators.
The 940B series has a built-in controller. It has a rangeability of less than 1/2000.
Standard specifications
|
Asahi Model number
|
Asahi HL regulator 942BA1
|
Asahi HL regulator 943BA1
|
Asahi HL regulator 944BA1
|
|
Valve function
|
Relief pressure control
|
|
Working pressure range
|
Maximum 1.0 MPa
|
|
Input signal * 1
|
0-5V (0-10V / 4-20mA / other, please specify)
|
|
Pilot pressure
|
2/3 of maximum working pressure (depending on model)
|
|
Power supply
|
24 VDC
|
|
Connection diameter
|
1/4
|
3/8
|
1/2
|
|
Fluid used
|
Liquid, gas (Teflon, Viton, fluid that does not attack brass)
|
|
Input impedance
|
1 kΩ or more (voltage input) / 300 Ω or less (current input)
|
|
Mounting direction
|
Arbitrary (0 point drift within ± 1% may occur depending on the mounting direction)
|
|
control method
|
Force balance + PI control
|
|
Flow rate consumed
|
1.5LPM or less (standard type) to 5LPM or less (high speed type)
|
|
weight
|
0.8 kg
|
2.1 kg
|
2.3 kg
|
|
Insulation resistance
|
1 MΩ or more
|
|
Hysteresis
|
± 0.2% or less
|
|
Linearity
|
± 1% or less
|
|
Orifice diameter
|
4 mmΦ
|
8 mmΦ
|
16 mmΦ
|
|
response speed
|
0.5sec or less (Characteristic under no load)
|
|
Material
|
Body = Bsbm / Diaphragm = Teflon / Seal = Viton
|
NOTE
* 1 Change the last digit of the model number. (Example: 942NA3 / 4 ~ 20mA input)
1 = 0 ~ 5V / 2 = 0 ~ 10V / 3 = 4 ~ 20mA / 5 = Other, please specify)
* 2 It is mainly used for liquid / gas split ratio control and mixing ratio control. It is used in a system that uses a concentration sensor, flow rate sensor, and temperature sensor together.
* 3 The standard uses a metal seal, which does not result in a completely closed state. Please contact us if you need a completely closed state.
* Please contact us for detailed dimensions and characteristic data.
Asahi HL regulator 910B series
HL Regulator
910B series
Multi-function high precision type
The 910 series is a 3-port multi-function servo valve. It can be used to control fluid mixing ratio, diversion ratio, flow rate, pressure, etc.
Compatible with fluids with a maximum operating pressure of 1.5 MPa and a maximum operating temperature of 150 ° C or less. It is very effective for controlling special fluids under conditions that cannot be used with hyper regulators.
The 910B series has a built-in controller.
It has a rangeability of less than 1/2000.
Standard specifications
|
Asahi Model number
|
Asahi HL regulator 913BA1
|
Asahi HL regulator 914BA1
|
Asahi HL regulator 916BA1
|
|
Valve function
|
Opening ratio control
|
|
Working pressure range
|
Maximum 1.5MPa
|
|
Input signal * 1
|
0-5V (0-10V / 4-20mA / other, please specify)
|
|
Pilot pressure
|
0.3 MPa
|
|
Power supply
|
24 VDC
|
|
Connection diameter
|
1/4
|
3/8
|
1/2
|
|
Fluid used
|
Liquid, gas (Teflon, Viton, fluid that does not attack brass)
|
|
Input impedance
|
1 kΩ or more (voltage input) / 300 Ω or less (current input)
|
|
Mounting direction
|
Arbitrary (0 point drift within ± 1% will occur depending on the mounting direction)
|
|
control method
|
Force balance + PI control
|
|
Flow rate consumed
|
1.5LPM or less (standard type) to 5LPM or less (high speed type)
|
|
weight
|
2.2 kg
|
3.4 kg
|
6.8kg
|
|
Insulation resistance
|
1 MΩ or more
|
|
Hysteresis
|
± 0.2% or less
|
|
Linearity
|
± 1% or less
|
|
Orifice diameter
|
6 mmΦ
|
10 mmΦ
|
14 mmΦ
|
|
response speed
|
0.5sec or less (Characteristic under no load)
|
|
Material
|
Body = Bsbm / Diaphragm = Teflon / Seal = Viton
|
NOTE
* 1 -Change the last digit of the model number. (Example: 904NA3 / 4 ~ 20mA)
1 = 0 ~ 5V / 2 = 0 ~ 10V / 3 = 4 ~ 20mA / 5 = Other, please specify)
* 2 - It is mainly used for liquid / gas split ratio control and mixing ratio control. It is used in a system that uses a concentration sensor, flow rate sensor, and temperature sensor together.
* 3 -The standard uses a metal seal, which does not result in a completely closed state. Please contact us if you need a completely closed state.
* Please contact us for detailed dimensions and characteristic data.
Asahi Enterprise Measurement and monitoring products
Asahi Gap sensor 616 series
Gap sensor
616 series
Seating sensor for positive pressure
Gap sensor 616 is a precise gap detection switch that outputs an contact signal by detecting an object approaching the air ejection hole by changing the back pressure in the ejection hole.
There are 616J type with hysteresis less than 5μm, 616JX type with less than 1μm hysteresis, and 616A type with less than 0.05μm hysteresis.
The J and JX types use only air pressure for detection, so no power supply is required. The output signal is taken out as a contact signal.
Since the 616A type uses a pressure sensor, a 24V power supply is required. An ON-OFF signal and an analog signal proportional to the gap are output.
Standard specifications
|
Asahi Model number
|
Asahi Gap sensor 616J1
|
Asahi Gap sensor 616J3
|
Asahi Gap sensor 616JX1
|
Asahi Gap sensor 616JX3
|
Asahi Gap sensor N6S
|
|
Supply pressure
|
100-250kPa (600 option)
|
|
Detection gap (μm)
|
5 to 200
|
10 ~ 300
|
0 ~ 800
|
0 ~ 1200
|
~ 600
|
|
Hysteresis (μm)
|
~ 100≤5
|
~ 150≤10
|
~ 200≤1
|
~ 200≤1
|
~ 100≤0.05
|
|
~ 150≤10
|
~ 200≤20
|
~ 400≤5
|
~ 600 ≤ 10
|
~ 200≤0.1
|
|
~ 200≤20
|
~ 300≤30
|
~ 800 ≤ 20
|
~ 1200≤30
|
~ 600 ≤ 0.2
|
|
Connection diameter
|
G1 / 8 (Ps)
|
|
Conduit port
|
Pf1 / 2 (Din connector, protection class IP65)
|
R03R-R5F
|
|
Fluid used
|
air
|
|
Mounting direction
|
Any
|
|
Detection method
|
Diaphragm (Viton)
|
(SUS)
|
|
weight
|
500g
|
700g
|
400g
|
|
Output configuration
|
SPDT (Only a contact can be used with light)
|
0-6V
|
|
Rating specifications
|
1A / 250VAC, 1A / 20VDC
|
Open collector
|
|
Ambient temperature
|
0-80 ° C
|
0-40 ° C
|
Asahi Pressure transducer 601 series
Pressure transducer
601 series
Pressure-Pressure Transmitter / Flow-Pressure Transmitter
The flow rate sensor 601D is a high-speed, high-resolution flow rate sensor that is used as an internal or external package for the 900 series and 940 series.
Rangeability 1/20 Flow rate can be measured from minimum flow rate 0.1 CCPM to maximum flow rate 300 LPM. (Pure water conversion)
There are the 601D-D series that uses a differential pressure sensor that comes in direct contact with liquid (wetted parts material = SUS316L) and the 601D-R series (patented) that uses a sensor that does not come into contact with the measuring fluid. Both sensors measure the differential pressure between two points to calculate the flow rate, and the calculation result is linearized and output.
Stable high-speed closed-loop control is possible because it has a calculation speed of 1 msec or less.
Standard specifications
|
Asahi Model number
|
Asahi Pressure transducer 601D-D05
|
Asahi Pressure transducer 601D-D2
|
Asahi Pressure transducer 601D-D10
|
Asahi Pressure transducer 601D-R05
|
Asahi Pressure transducer 601D-D25 *
|
|
Line pressure (kPa)
|
100 ~ 300
|
|
Detected flow rate (CCPM)
|
5 ~ 100
|
100-2000
|
2500-50000
|
10 ~ 100
|
200-2000
|
|
Port size (G)
|
1/4
|
3/8
|
1/2
|
1/4
|
3/8
|
|
Conduit port
|
R03R-R5F
|
|
Fluid used
|
Liquid compatible with SUS316
|
Any
|
|
Mounting direction
|
Any
|
|
Detection method
|
Differential pressure measurement
|
|
weight
|
700g
|
600g
|
|
Power supply
|
24V
|
|
Analog output
|
0-5V
|
|
Ambient temperature
|
0-40 ° C
|
Türkiyede Asahi Enterprise ürünleri ile ilgili uygun rekabetçi fiyatları almak için müşteri temsilcimiz ile http://www.imajteknik.com.tr/bize-ulasin veya Fiyat teklifi formunu doldurarak mesaj bırakmanız halinde satış mühendislerimiz en kısa zamanda sizinle irtibat kuracaklardır.