Clavis Type Type 5 optical Tension meter
Clavis Type 5-sk-optical Tension meter
Clavis Type 5 acoustic belt meter
Clavis Type 5 optical belt meter
Clavis 5-sk-optical Tension meter
Type 5 acoustic belt gauge Clavis
Type 5 optical belt gauge Clavis
Clavis Type 7 optical belt meter
Clavis Belt Frequency Meter Type 7
Clavis Type 7 acoustic belt meter
Clavis Type 7 optical belt meter with optical sensor head
Type 7 acoustic belt gauge Clavis
Clavis Type 7
Clavis CLAV-012 sensor
Clavis Optical sensor head Type 12
Type 12 Optical head sensor Clavis
Clavis CLAV-012
Clavis 13 Sr Super Rugged Optical Belt Tension Calibrator / Digital Meter
13 Sr Belt Tension Meter Clavis
Clavis 13 Sr Belt Tension Meter
Clavis Timing Belt Cam Belt Meter
Clavis 13 Sr Super Rugged Optical Belt Tension Calibrator / Digital Meter
Clavis 13 Sr Belt Tension Meter Timing Belt Cam Belt Meter
Clavis Mulco Belt Tension Meter
Clavis belt tension meter
Type 7 optical belt meter with Type 12 optical sensor head
Clavis Handbrake Setting System
Drum Brakes
Clavis Drum Brakes The measurement operation is undertaken by placing measurement tools on each of the rear brakes. The measurement tool has a spring loaded sensor pin which remains in constant contact with the brake lever. The sensor pin is connected to a linear potentiometer from which the position of the brake lever can be determined.
The positions of the brake levers are communicated to a control cabinet which interfaces with an electronic power tool. The length of the handbrake cable is then adjusted by the power tool in response to the brake lever position information communicated by the measurement tools.
The sensor nose of the tool should be guided into the access hole on the brake back plate. As the sensor enters the back plate the magnets on the location arms ‘snap’ the tool into position aided by the black nylon guide plates. The magnets securely hold the tool in position.
The brake drum has been removed for clarity.
Clavis Disk Brakes
The caliper lever position for a correctly set brake is defined by the manufacturer of the brake. The aim is such that any cabin lever movement should translate into brake lever movement and increase braking effort.
When the cabin lever is in the fully down position there should be no brake drag.
The caliper lever should be advanced by the setting operation so that there is a gap between the lever and the rest stop bracket. The caliper lever is in constant contact with a spring loaded sensor arm (connected to a linear potentiometer) within the measurement tool.
The disk measurement tool has a clamping mechanism which pulls the tool hard against the caliper. This is achieved by pressing the locking handle down which in turn rotates a cam. The cam operates against a pivoted arm which moves a ‘flipper’ under the body of the caliper. The force which the flipper exerts onto the body is determined by a spring contained within the pivoted arm.
Clavis Handbrake Setting System
CLAVIS BELT METERS
TYPE 3 BELT METER
The Type 3 Belt Meter is suitable for measuring frequencies in all types of belts and outputting measurements in Hertz (Hz). This belt meter is available in Optical and Acoustic and is operated by a simple ON/OFF keypad button.
Type 3 Frequency Range
The Type 3 Optical has a frequency measurement range of 7Hz to 300Hz and uses an optical sensor head. This meter is useful where there is a requirement to measure tension in a variety of belts, some vibrating at low frequencies.
The Type 3 Acoustic has a frequency measurement range of 10Hz to 300Hz. The acoustic sensor is particularly suitable for belts which vibrate poorly or where the amplitude of belt vibration is very small
Measurement
This meter measures and displays readings from the belt under tension in Hertz (Hz) only.
Clavis Type-3
CLAVIS TYPE 4 BELT METER
Clavis hand held Belt Tension Meter Type 4
Clavis Type 4 acoustic belt tension meter
Clavis Belt Tension Meter Type 4
Type 4 acoustic belt tension meter Clavis
The Type 4 Belt Meter measures in Hertz (Hz) and is operated by a simple ON/OFF keypad button. All belt types are suitable including toothed timing belts and poly-vee belts. This belt meter is available in Optical and Acoustic.
Type 4 Frequency Range
-
The Type 4 Optical has a frequency measurement range of 10Hz to 600Hz and uses an optical sensor head. This meter is useful where there is a requirement to measure tension in a variety of belts, some vibrating at low frequencies.
-
The Type 4 Acoustic has a frequency measurement range of 30Hz to 600Hz. The acoustic sensor is particularly suitable for belts which vibrate poorly or where the amplitude of belt vibration is very small.
Measurement
This meter measures and displays readings from the belt under tension in Hertz (Hz) only
Clavis Type-4
CLAVIS FOURIER BELT MEASUREMENT SYSTEM
The FourierBMS measures the tension of the drive belt using an optical sensor head.
Türkiyede Clavis ürünleri ile ilgili uygun rekabetçi fiyatları almak için müşteri temsilcimizle ( http://www.imajteknik.com.tr/bize-ulasin ) veya Fiyat teklifi formunu ( http://www.imajteknik.com.tr/online-iletisim-formu ) doldurarak mesaj bırakmanız halinde satış mühendislerimiz en kısa zamanda sizinle irtibat kuracaklardır.