Dart Controls
- Electronic DC Variable Speed Controls (fractional through 3 horsepower)
- Digital and Analog DC Speed Controls
- Battery Powered Controls (chassis mount and enclosed versions)
- DC Brushless Controls (chassis mount and enclosed versions)
- Tachometers (chassis mount and enclosed versions)
- Pick-up Sensors (chassis mount and enclosed versions)
- DC Permanent Magnet Motors
150 Series OEM SCR Control
Single or Dual Voltage 120/240 VAC, 50/60Hz
Adjustable horsepower settings
Male spade terminations standard
Full wave bridge supply
1% speed regulation, ±1/2% with tach feedback
Adjustable Minimum speed
Adjustable Maximum speed
Adjustable IR Compensation
Adjustable Current Limit
Adjustable Acceleration
Adjustable Deceleration
Line voltage compensation
5K ohm speed pot, knob & dial plate included
50:1 speed range
Overload capacity: 200% for one minute
Transient voltage protection
Voltage following mode
Inhibit circuit
125D 1HP DC Speed Control
Dual Voltage 120/240 VAC, 50/60Hz
Adjustable horsepower settings
Barrier terminal strip
Full wave bridge supply
1% speed regulation, ±1/2% with tach feedback
Adjustable Minimum speed
Adjustable Maximum speed
Adjustable IR Compensation
Adjustable Current Limit
Fixed Acceleration
Optional Adjustable Acceleration
Line voltage compensation
5K ohm speed pot, knob & dial plate included
50:1 speed range
Overload capacity: 200% for one minute
Transient voltage protection
Voltage following mode
Inhibit circuit
125DV200E 2HP NEMA 4X Enclosed
UL Listed, all models
MOV transient protection
Adjustable linear ACCEL and DECEL adjustment
Adjustable minimum and maximum speed limits
Adjustable Current Limit and IR Compensation
Line fused
Power ON/OFF switch
Power "ON" indicator
NEMA 4X enclosure
Auto Sensing Dual Voltage 120/240VAC input
Output Voltage 0-90/180Vdc
1% speed regulation; 50:1 range
HP adjustable over 1/4 to 2HP range – no jumpers or resistors to change
Overload capacity 200% for 1 minute
253G 2HP DC Speed Control
Dual voltage - 120/240 VAC, 50/60Hz
Adjustable horsepower settings
Barrier terminal strip
Packaged bridge supply (fullwave)
1% speed regulation; ±1/2% with tach feedback
Adjustable Minimum speed
Adjustable Maximum speed
Adjustable IR Compensation
Adjustable Linear Acceleration
Adjustable Current Limit
Line voltage compensation
5K ohm speed pot, knob and dial included
Power on/off switch (enclosed models)
50:1 speed range
Overload capacity: 150% for one minute
Transient voltage protection
Inhibit circuit
Enclosed models rated NEMA 4/12
15 Series FHP DC Speed Control
Dual voltage models of 12/24 VAC or 120/240 VAC input
Full wave bridge power supply > Adjustable Minimum speed
Adjustable Minimum speed
Adjustable Maximum speed
Adjustable IR Compensation
Fixed Acceleration
5K ohm speed pot, knob & dial included
25:1 speed range
1% speed regulation
Overload capacity of 200% for 1 minute
Transient voltage protection
AC line fuse (Enclosed)
Power on/off switch and light (Enclosed)
130 Reversing DC Speed Control
Adjustable horsepower settings
Barrier terminal blocks
Full wave bridge supply
Adjustable Min speed
Adjustable Max speed
Adjustable IR compensation
Adjustable current limit
Fixed accel (0.5 sec)
Line voltage compensation
5K speed pot, dial and knob included
50:1 speed range
Overload capacity: 200% for 1 min
Transient voltage protection
Onboard dynamic brake resistor
Automatic DB on power loss
1% speed regulation
530B 3HP DC Speed Control
Dual 120/240 VAC, 50/60Hz via slide selector switch
Adjustable horsepower settings
Barrier terminal strip
Packaged bridge supply (fullwave)
1% speed regulation; ±1/2% with tach feedback
Adjustable Minimum speed
Adjustable Maximum speed
Adjustable IR Compensation
Adjustable Linear Acceleration (0.3 to 12 sec.)
Adjustable Linear Deceleration (0.6 to 12 sec.)
Adjustable Current Limit
Line voltage compensation
5K ohm speed pot, dial and knob included
50:1 speed range
Overload capacity: 200% for one minute
Transient voltage protection
Inhibit circuit
Enclosed models rated NEMA 4/12
MD10 / MD3 Digital DC Drive
Adjustable min/max
Adjustable accel/decel
Closed-Loop digital speed regulation
Programmable power-up drive settings
Drive Inhibit mode
Jog function
Non-volatile memory preserves settings
Factory default restore function
User-default restore function
Front-panel parameter lockout
Programmable display in any rate or time units
Custom front panel artwork available
NEMA 4X rating both panel mount and stand alone enclosed models
Universal power supply - any input 85–265 VAC
Two (2) user-defined alarm contact outputs
Multiple operational modes: Rate, Time, Follower
MD40 / MD50 Digital DC Drive
1/50 to 2.0 adjustable HP range
Universal power supply supports 85-265 VAC in
1/8 or 1/4 DIN panel mount with NEMA 4X faceplate, NEMA 4X stand-alone enclosure
Front panel field-programming (with lock-out jumper)
Display speed in any engineering unit of measure
Two alarm relay outputs (form C, 5 Amp @ 250 VAC)
Large 1/2˝ LED display
Master/Follower modes
Displays set point or actual running speed
Adjustable PID settings
Optional your company name/ logo on the cover
DP4 Digital Potentiometer
Field programmable Rate or Time modes
Inhibit function
Jog function
Factory default restore
User-default storage and restore
NEMA 4X Rating (with supplied gasket)
Supports bidirectional connections for regenerative drives
ASP10 SMART Speed Pot
Configurable min/max speed
Configurable accel/decel rates
Configurable P-I parameters
Pulse feedback required - up to 50K/min
Configurable power-up modes
Inhibit mode
Jog mode
User-friendly menu driven programming from front panel
Parameter lockout to save settings
Configurable display units and decimal point
Custom display bezel artwork available
NEMA 4X Rating (with supplied gasket)
Dual Supply 120/240VAC
User configured output for status and diagnostics
Non-volatile memory
Factory default restore
User-default restore
ASP40 SMART Speed Pot
Microprocessor-based design
ModularBus expansion accomodates a wide variety of I/O
Ideal for PLC/SCADA controlled systems
Digital closed-loop P-I-D algorithm delivers accuracy of ± 1/2 pulse (feedback)
Optional open-loop operation available
Non-volatile memory maintains user configuration
Field programmable
Speed profile parameters include MIN, MAX, ACCEL, DECEL
Programming lockout feature
Universal power supply accepts any line voltage inputs from 85-250VAC @ 50-60Hz
Transient voltage protection
Compatible with many speed
Two programmable alarm/status outputs
Configurable user inputs support Inhibit, Emergency-Stop, and Jog functionality
Large 4 digit, 1/2” LED display configurable in rate or time units, including decimal point
Multiple operating modes including Master and Follower
NEMA 4X when used with gasket (provided)
DP10 Signal Conditioner / Generator
NEW!
Signal converter (mA to voltage or vice-versa)
Signal attenuator (0-100% scaling of input signal, voltage or mA)
Signal generator (volts or mA)
mA loop power provided
Scalable display in engineering units
Configurable front panel lockout feature
700BDC/730BDC 12-48V Brushless DC Drive – 480W
NEW!
Adjustable MIN and MAX speed; CURRENT LIMIT
Adjustable ACCEL/DECEL (703B/ 733B only)
150% overload for 30 seconds
Field selectable motor hall spacing
50:1 speed range
FWD/ REV feature
BRAKE feature (730B Series only)
Current Limit Latch feature (733BDC only)
710ADC Low Voltage Brushless DC Drive – 1000W
Adjustable MIN and MAX speed; CURRENT LIMIT
200% overload for 30 seconds
Field selectable motor hall spacing
50:1 speed range
FWD/ REV feature
BLM700 Brushless DC Drive /Tachometer
Microprocessor-based design
Digital closed-loop algorithm accuracy of ±1/2 RPM of set speed or equivalent
Non-volatile memory maintains drive settings on power loss
Factory or field programmable via front-panel keypad
Control profile settings include MIN and MAX speed, ACCEL, DECEL, display units, and more
Programming lockout feature
Transient voltage protection
Self-contained power supply for speed pickups
Large 4 digit, 1/2” LED display
Durable NEMA 4X rated aluminum housing with Polycarbonate membrane and gasket
Ambient temperature range of -10°C to 45°C
Multiple operating modes including: Master, Rate Mode – Controls in rate unit such as RPM, Gallons per Minute, etc. Master, Time Mode –Controls in time unit such as HH:MM, MM:SS, SS:TT, or other unit
60 or 120 Hall Sensor spacing - jumper selectable
Forward or Reverse rotation of motor is jumper selectable
65E Low Voltage Drive (20A)
Compact PWM motor speed control for low voltage applications
Rated for 10 or 20 amps continuous current, the 65E10/65E20 Series are compact PWM controls for 12 thru 48 volt DC (jumper selectable) battery powered applications. Features include adjustable maximum speed, minimum speed, current limit, I.R. compensation, and acceleration, plus a quiet operating frequency of 18kHz. NEW FEATURES include current limit shutdown and drive status LED’s.
- Smooth, quiet 18kHz switching
- NEMA 4X enclosed models
- Saves battery charge for longer operation / life
- High efficiency MOSFET's reduce voltage drop
- Speed regulation is ±1% of base speed
- Adjustable MAX and MIN speed; IR COMP; CUR LIM; ACCEL
- Accepts 0-10Vdc speed signals
- Inhibit input for low power start/stop switching
- Current limit shutdown and output
- Supply voltage and Current Limit status LED's
65E Low Voltage PWM Drive (60A)
PWM motor speed control for low voltage applications rated to 2000W
65E Series standard features include: Adjustable MIN, MAX, ACCEL, IR COMP, and CUR LIM, low battery compensation, analog armature feedback, speed potentiometer with leads, knob and dial plate. Available for 12 thru 36DVC, 40 and 60 Amp continuous motor ratings.
Saves battery charge for longer operation / life
High efficiency MOSFET's reduce voltage drop
Speed regulation is ±1% of base speed
Adjustable MAX and MIN speed; IR COMP; CUR LIM; ACCEL
Accepts 0-10Vdc speed signals
Inhibit input for low power start/stop switching
Current limit
PU Series Speed Pickup
Popular encoder with 1 to 20 PPR output
NPN, Sinking Source, 5-24VDC
For indoor (PU-E Series) and outdoor / wash down applications (PU-R Series)
Drill and tap, single bolt installation
No alignment necessary
Pickup Kit (CF)
For NEMA 56 and NEMA 143TC, 145TC, 182C, 184C Frame motors
1 to 60 PPR output, 5-24VDC, NPN Sinking Source
Photoelectric Optical Pickup (OPU)
Hall-effect output, 5VDC, NPN Sinking Source
For applications where C-face, drill and tap installation not possible
Standard Stock DC Motors
NEMA frame motors with removable base
1/4 thru 1 1/2 HP; 90 and 180VDC permanent magnet
Drilled and tapped to accept Dart PU Series encoder
In stock and ready to ship
AC03 Triac AC Motor Speed Control
- Controls most single phase AC motors and restrictive loads, not equipped to handle capacitor start motors
- Speed pot with on/off switch
- Minimum output adjustment
55AC Triac AC Motor Speed Control
Controls most single phase AC motors and restrictive loads, not equipped to handle capacitor start motors
For vibratory feeder, fan, pump, heating, and lighting industries. All models feature single-phase AC input and fully variable AC output
Enclosed version includes power on/off switch, power on indicator lamp and front access fuse
Triac switching to vary output phase and thus speed of (compatible)
4-in-1 Programmable Tachometer
NEW! Shared Display Tachometer Accepts Two Speed Inputs
Big, bright 1/2" LED display
Scalable Rate, % and Time units
Single, or dual encoder input with shared display
Multi-purpose tachometer, counter, totalizer or Zero speed Switch
Single (std) or two relay alarm output
Up to NEMA 4X rating (determined by cabinet)
VSI2 – Signal Follower Option
NEW – Jumper Selectable DC volts or 4-20mA Operation
Provides isolation for signals originating from non-isolated sources
4-20mA or analog voltage signals from 0-5 to 0-250VDC
MSC38A Master Speed Control
For applications where multiple drives are adjusted from a single potentiometer, analog voltage or mA signal
Dart Controls Ürünleri ile uygun rekabetçi fiyaları almak için müşteri temsilçimiz ile http://www.imajteknik.com.tr/bize-ulasin veya Fiyat teklifi formunu doldurarak mesaj bırakmanız halinde satış muhendislerimiz en kısa zamanda sizinle irtibat kuracaklardır.