Ronan Measurements Division

Ronan Measurements

Nükleer Seviye, Yoğunluk ve Tartım Sistemleri, Ardışık Olay Kaydı

Öncü enstrümantasyon ve sistem üreticileri. Şiddetli servis ortamlarında gerçek zamanlı izleme ve kritik süreç kontrol noktalarının ölçüm sağlayıcıları.50 yıllık geçmişimiz boyunca Ronan, Kaliforniya, Kentucky ve Birleşik Krallık'ta imalat, satış ve servis tesisleri kurdu.

Ronan Measurements Division   Products

  • Source Holders
     
  • Density
     
  • Mass Flow
     
  • Continuous Level
     
  • Interface Level
     
  • Point Level
     
  • Mold Level
     
  • Weighing System
     
  • Radiation Monitoring Systems
     
  • PC Based Software
     
Ronan has the most sensitive systems in the industry, and as such is able to provide source sizes in the microcuries (kBq) in installations where others would provide sources in the millicuries (MBq.)  This is achieved while still delivering the same (often better) high accuracy and stability of other systems.  Ronan's confidence in our products is so high that we provide a three (3) year warranty on our electronics and a guaranteed source working life of 15 years.
 
Ronan is able to achieve this level of sensitivity by engineering your systems to meet your specific applications and requirements. Ronan uses the widest range of detector materials available, including Sodium Iodide (NaI), Plastic or Liquid Scintillation for low-level applications, and Ion Chamber and Geiger Mueller for applications where the gamma energy at the detector is higher.
 
Retrofit your old system and save Thousands! If you have an older system, it is probable that we can replace your detector with scintillation technology, upgrade your electronics to the latest available, and use your existing old source. This gives you the benefit of a new system which is easier to calibrate and maintain, with better accuracy and stability than the existing one…all while saving thousands of dollars on disposal costs of the old source, and having to buy a new one.
 
Density
 
Ronan Density systems are mounted externally to the pipe via brackets, or internally in dry wells, and can be installed while the process is running. The instruments have no wetted parts and are ideal for liquid processes where traditional contact technologies cannot be used.
 
  - Measurement Not Affected By:
 
            Internal Obstructions
            Extreme Process Temperatures
            Caustic Products
            Slurries
            Violent Product Flow
            Sterile Process
            Changing Process
 
 - Mounts External to Existing Pipes with No By-Pass Lines
 - Display in Customer-Specified Units
 - Most Applications Utilize Low Energy Sources
 - Push Button to Calibrate
 - Empty Pipe Monitor
 
Mass Flow
 
 
The Mass Flow system consists of a Ronan Density guage with an input from a volumetric flowmeter, such as a magnetic flowmeter. The Ronan guage is mounted externally to the pipe via brackets, or internally in dry wells, and can be installed while the process is running. The instruments have no wetted parts and are ideal for liquid processes where traditional contact technologies cannot be used. 
 
  - Measurement Not Affected By:
 
            Internal Obstructions
            Extreme Process Temperatures
            Caustic Products
            Slurries
            Violent Product Flow
            Sterile Process
            Changing Process
 
 - Mounts External to Existing Pipes with No By-Pass Lines
 - Display in Customer-Specified Units
 - Most Applications Utilize Low Energy Sources
 - Push Button to Calibrate
 - Empty Pipe Monitor
 
Continuous Level  
 
Ronan Continuous Level Systems utilize either solid crystal or liquid scintillation material, depending on the application.  The FlexDetector™ is an innovative design which is lightweight, contours to the shape of your vessel and is available in single lengths up to 23 Feet (7 meters). For longer level measurements, up to six detectors can be summed in a single X96S computer giving an overall continuous level measurement up to 138 feet (42 meters.)
 
- Solids or Liquid Measurement
- Measurement Not Affected By:
 
         Internal Obstructions: i.e. Agitator
         Extreme Process Temperatures
         Caustic Processes
         Violent Product Flow
         Sterile Process
         Changing Process
         Variable Product Flow
         Automatic Compensation for Vapor Density Changes
         Automatic Compensation for Foam or Gasses
         Automatic Compensation for Process Build-Up
         Detectors Contoured to the Shape of Vessels
         Solid or Flexible Designs
 
- Low Maintenance / No Component Wear
 
Interface Level
 
Interface Level and Process Density Vessel Profile Measurements
 

The Ronan interface system solves the problems of accurately detecting and measuring interface level, process density and product profiles.  By using non-contact technology, no components are wetted to the process, making it ideal for processes with harsh conditions, such as: high temperature, high pressure, corrosive, abrasive, or toxic. Typically, the measurement is repeatable to a process density of +/-0.005 SpG and ½ inch (13 mm) level. System configuration can be for Interface Level or Process Density Profile.

Features
 
- Motor Driven or Static System
 
- Measures up to 100 Feet (30 Meters)

- Ability to Track Specific Interface(s) or Profile(s) including Liquids, Gasses and Foam

- Display of Interface Level, Source Level and Process Density

- Ability to Adjust for Density Changes of Stratified Layers

- Remote Control Capabilities

Point Level

The X90 Point Level Monitor detects the presence or absence of material at a given point in a tank, hopper, chute or process pipe. All components are mounted externally to the process vessel making the system ideal for monitoring the most dangerous materials such as caustic, toxic, corrosive, explosive, and carcinogenic irrespective of their temperature. The modular design is ideal to upgrade older systems while keeping the existing sources.
 
Mold Level
 
Ronan Engineering introduces the new X96 ML mold level system with an unmatched update time of 10 ms, and fast "Cast Start" capability. The user is now able to obtain high-speed sampling of the level of steel in the mold, giving better control and enabling the user to increase throughput and improve quality.

Ronan differentiates itself from competitors through its unmatched service and repair organization and innovations in technology to improve both safety and the ability to control the level of molten metal. In 1999 improvements in detector and microprocessor technology enabled Ronan to be the first in introducing the RLL Device with source activities generally 100 times less than the normal amount required. The lower levels of activity not only provide a safer working environment; they also exempt the user from having to obtain a Specific License, Wipe Tests and Surveys.

 

Ronan’s experienced engineering team will work with the end user and/or OEM company from the design phase of a project through the commissioning phase to ensure the seamless integration of the level measurement to the mold design and control specifications.

 

For mills where the user is already using gamma technology, Ronan offers a cost-effective solution to upgrade to this latest technology while utilizing existing sources, irrespective of original manufacturer. In cases where the user has a large inventory of detectors, solutions are available where those can still be used, thus increasing the cost-effectiveness of upgrading.
 
Weighing System
 Ronan Ölçeği tartılır 
 
The Ronan non-contact weigh scale is an economical approach for solids weighing on belt and screw conveyors.  The system can be installed by simply bolting the frame around the conveyor, without the need to make any costly adjustments to the conveyor itself.  The lightweight, compact design enables it to be located in areas where space is a limitation and without the need for additional supports or foundations.
 
Features
 
- Most Measurements Made with Low- level Sources (0.9 mCi 0.033 GBq)
 
- Automatic Zero on Empty Conveyor
 
- Absorber Plates for High Calibration
 
- Lightweight
 
- Low Maintenance / No Component Wear
 
- Batching Capability
 
 
Display and Outputs (Customer Selectable Units)
 
- Speed
 
- Weight
 
- Rate
 
- Totalizer
 
 
Radiation Monitoring Systems
 
 Portal Monitoring Systems
 
The XSD-1000 radiation detection system detects the presence of very low-levels of gamma radioactive materials hidden within a vehicle or container. In industrial applications the system is invaluable in helping catch radioactive material in scrap material before it enters a facility and causes contamination, resulting in costly cleanup expenses. Use of the system in areas of interest for homeland security provides for the early detection of gamma radiation materials, which could be used as a threat to national security.

The Ronan XSD-1000 radiation detection system is modular and expandable in design to meet your specific detection needs. A variety of detector and frame configurations are available to meet any application. The system operates on a windows environment with touch screen navigation for ease of configuration. All data is presented in an easily understood format without the need for the operator to have an understanding of physics.

Each system configuration is optimized for the particular type of transportation system being monitored. The system sensitivity is such that not only does it detect the presence of a target source, it also pinpoints the location of the isotope within the vehicle or container. In comparative testing with other systems on the market, Ronan was found to have the best sensitivity, with an ability to detect target radioactive isotopes at significantly lower levels than the other systems
 
PC Based Software

Ronan X96S Access Software is a package of integrated software tools designed for your PC in a Windows environment. Access software allows you to configure, calibrate, troubleshoot, tune, linearize, log data (real time), review past trends (history), save configurations and restore old configurations to the Ronan X96S microprocessor.

Special Features include:

  • Automatic Linearizer. Simply turn on the linearizer, allow the vessel to fill and the software calculates up to 32 points of correction. The software displays the points graphically. You can modify any of the points and the software then transfers the points automatically to the X96S. There is no need to stop and start the fill process while taking manual readings. The benefits are better linearizeration and less time spent on calibration.
  • Real time trends. Allows you to monitor trend level, density, weight, detector counts, detector temperature, process temperature, belt speeds, flow rates, and alarms.
  • Save & Restore Configurations. Allows you to save and restore your X96S parameters onto your PC for later use.
  • Ronan Filter tuning. Tune your applications "off line" without worrying about upsetting your process. Using data from saved trends, you can test new filter settings and see the results offline. Once you have determined the desired settings you can transfer these settings to the microprocessor.
  • Event Recordings. Access the event recording saved by the Ronan X96S microprocessor to aid in troubleshooting and monitoring modifications to the Ronan X96S microprocessor

Source Holders

RLL 

 
Safest on the Market  

RLL is a Ronan Engineering term that stands for "Radiation Low Level." RLL technology utilizes up to a total of 0.9 mCi(0.033 GBq)  of cesium source.  In comparison, some conventional density gamma gauges use source sizes with a hunderd times more activity to make the same measurement.  Because of these very low-levels of activity, and their simplicity of design, Ronan systems are the safest gamma gauges on the market.  The NRC recognized this in 1999 when Ronan Engineering attained certification for the first RLL source design.

There are three types of RLL Source Holders; the RLL-1, RLL-1A, and the RLL-2.  The RLL-1 utilizes from one to ten 0.09 mCi (0.003 GBq)  cesium capsules, while the RLL-1A utilizes a single 0.9 mCi (0.033 GBq) cesium capsule.  The RLL-2 is a strip source holder which accomodates up to a total of 100 µCi (0.004 GBq) cesium 137. 

- Periodic shutter check.  Per NRC guidelines, shutters are not required on source holders with less than 1 mCi (0.037 GBq) of cesium.

- No Radiation Safety Officer and/or Special Radiation Training is Required by NRC

- No Licensed Radiation Person is Required to Install, Commission or Move On-Site

Other advantages include:
 
- 0.5 mrem/hr @ 12"
 
- Lower Disposal Cost Than Conventional, Higher Intensity Type Gages
 
- Lead Free Option Available
 
- Fire Resistant Design Available
 
- Less Risk to users
 
- Less Documentation to Maintain
The only regulatory difference between the RLL-1 and the RLL-1A is that the RLL-1 does not require a Leak Test, whereas the RLL-1A requires a leak test every three years.  This exemption from leak tests is an advantage for the RLL-1.  However, because it utilizes multiple capsules, and the RLL-1A utilizes only one capsule, the RLL-1 is more expensive than the RLL-1A.

 

Ronan sizes the source to last a minimum of 15 years, usually 20- 30 years.  We guarantee a minimum of 15 years on all sources.

Total Cost of Ownership

 

Even though the initial equipment cost may be approximately 10% higher than conventional gamma gauges, the return on investment is almost immediate.  The differential in equipment costs are offset by lower installation costs (RLL sources do NOT require licensed personal to install, commission or move them… conventional sources require licensed personal.)  On-going maintenance costs are also lower as the RLL does NOT require periodic leak tests (RLL-1) or shutter checks as conventional sources do.
 
- The RLL Type Gauge is Approximately 100 lbs (45 kg), Lighter Than Conventional Type Gamma Gauges and as Such are Easier to Install...No Supports Required on Smaller, Lighter Piping

- The RLL is Smaller in Overall Dimensions (6 in, 15 cm) Than Conventional Type Gamma Gauges

- Dependable, Reliable, Repeatable Measurement That is Easy to Install, Calibrate and Maintain

 

Ronan can utilize low-level technology because our only focus is on non-contact measurement gauges. We use extra sensitive scintillation type detectors.  We cut and polish the crystals at our facility.  We utilize spring pressure to hold the crystal securely to the photo-multiplier tube.  We do not use cements, glue or grease that can degrade or break the connection between the crystal and photo-multiplier tube.  Ronan typically uses larger crystal sizes, which enables us to measure a larger sample of the product in the pipe. Ronan’s microprocessor utilizes the latest technology in the industry
 
 
 
SA-1
 
General Purpose Source Holder
 
 
The SA-1 is a rugged, general purpose source holder suitable for a wide range of applications requiring an externally mounted source. The SA-1 provides shielding which meets all international standards for radiation limits, and accomodates source activity up to 5 Curies (185 GBq) CS-137 or 18 mCi (0.67 GBq) Co-60. 
 
Features

- Ductile Iron cast with epoxy paint as standard. Available in Stainless Steel and PVC coated ductile iron as options for harsh environments

- Lead Free Option Available
 
- Fireproof Design Available
  
- Manual Rotary Shutter as Standard. Options include: Shutter Position Indicator Contact Output, Air or Electric Actuated Shutter with Position Indicator Contact Output.
 
 
GS-400 
 
The Ronan GS-400 Source Holder is a Fireproof Rated Design which mounts externally to the pipe or vessel.  With a collimation angle of up to 90 Degrees, it is ideal for continuous level applications where multiple sources would normally be required. The GS-400 is available in a variety of sizes, providing shielding which meets all international standards for radiation limits, and accommodates up to 10 Curies (370 GBq), CS-137 and 2 Curies (74 GBq), Co-60.
 
Features 

- Ductile Iron with epoxy paint as standard. Available in Stainless Steel or PVC coated ductile iron as options for harsh environments

- Up to 90 Degree Collimation Angle
 
- Fireproof Design
  
- Manual Rotary Shutter as Standard. Options include: Shutter Position Indicator Contact Output, Air or Electric Actuated Shutter with Position Indicator Contact Output.
 
 
GS-200 and GS-300 
 
External or Well Mount Source Holders
 
The GS-200 and GS-300 Source Holders are physically small cylindrical, stainless steel source holders which are designed for either external mounting via brackets or clamps or internal mounting in a well.  They are ideal for installations where space is restricted.  The GS-200 is collimated up to 37 Degrees and shields up to 50 mCi (1.85 GBq) CS-137 (Strip or Point Source), while the GS-300 is collimated up to 90 Degrees and shields up to 70 mCi (2.59 GBq) Cs-137 (Strip or Point Source.) Both Source holders meet all International Standards for surface radiation limits.
 
 Features
 
- Stainless Steel Construction
 
- Lightweight, 25 lbs
 
- Manual Rotary Shutter. Optional: Shutter Position Indicator Contact Output. Air or Electric Actuated Shutter with Position Indicator Contact Output
 
 
SA-4, SA-10, SA-15
 
 Well Mount Source Holders
 
The SA-4, SA-10 and SA-15 family of source holders are designed for installations where the source is inserted into a well. The most common applications are thick-walled or large diameter vessels or molds, thus enabling a lower size isotope to be used than would be required if using externally mounted source holders.
 
Features
 
- Source Activities up to:
                                 - SA-4:     2 Curies (74 GBq) Cs-137, 20 mCi (0.74GBq) Co-60
                                 - SA-10: 20 Curies (740 GBq)Cs-137, 100 mCi (3.7 GBq) Co-60
                                 - SA-15:    300 mCi (11 GBq), Cs-137, 5 mCi (0.18 GBq) Co-60
 
- Continuous Welded Carbon Steel Housing with Epoxy Paint
 
- Insertion Length per Customer requirement
 
 
LS-S and LS-D
 
Single or Dual Port Source Holders
 
 
The LS series of source holders are available with either single or dual ports for the radiation beam.  The dual port has two collimators, 180 degrees apart which enable a single source holder to be used to provide the measurement beams for two vessels, when the vessels are close to each other i.e. Flyash Hoppers.  This provides significant cost savings as only half the sources are required than would normally be needed with single beam configurations.  The sources accomodate up to 150 mCi (5.6 GBq) Cs-137 and meet all International Standards for Surface Radiation Limits
 
The LS source holders are approved for General License installations on level applications when used with an interlock device.
 
Ideal for Flyash Hopper Installations
 
Features
 
- Stainless Steel Housing
 
- Dual or Single Port Configurations
 
- Lightweight...55 lbs (25 kg)
 
- Shutter Options Include: Remote Cable, Remote On/Off Indicators, Intelocking Device, Air Actuation
The RLL-1 and 1A are very similar in that neither require:
 

Ronan Ürünleri ile uygun rekabetçi fiyaları almak için müşteri temsilçimiz ile  http://www.imajteknik.com.tr/bize-ulasin veya Fiyat teklifi formunu doldurarak mesaj bırakmanız halinde satış muhendislerimiz en kısa zamanda sizinle irtibat kuracaklardır. 

Ronan Measurements Division markasına ait tüm ürünler

    0 kayıt bulundu

      ALFABETİK MARKA LİSTESİ

      Ürün Gruplarına Göre Filtrele

      Sertifikalarımız

      Oruçreis Mah. Tekstilkent Tic. Mrk.
      G2 Blok, No:101 (10AD-Z77)
      34235 Esenler / ISTANBUL
      T: +90 212 235 95 35 / 36
      F: +90 212 235 95 37

      info@imajteknik.com

      E-Bülten Listemize üye olun !

      Gelişmelerden haberdan olmak ve ileride gerçekleştirilecek yeniliklerimizden haberdan olabilmek için e-posta adresinizi bizimle paylaşın!

      Copyright 2014 İmaj Teknik - Tüm hakları saklıdır.