Products
Vibro-Meter UK (Rugby) leads the world in the design and manufacture of ignition systems for gas turbines, microturbines, petrochemical and industrial burners.
- High Energy Ignition Systems
- High Tension Ignition Systems
- Flameproof Ignition Systems
- Torches with integral H.E. Igniters
- Custom designed Ignition Systems
- Igniters
- Cables
- Exciters
- Cable Fittings
- Flame Detection
- Probes
- Level Probes
Markets Served
- Gas Turbine
- Micro turbine
- Petrochemical
- Industrial
ABA 171
The ABA 171 industrial housing can contain up to 2 signal conditioners and is available in two versions: a standard version and a version approved for use in potentially explosive atmospheres. Both versions are configurable and can be ordered with various cable fittings (stuffing glands) to support different signal conditioners and cables.
ABA 172
The ABA 172 industrial housing can contain up to 4 signal conditioners and is available in two versions: a standard version and a version approved for use in potentially explosive atmospheres. Both versions are configurable and can be ordered with various cable fittings (stuffing glands) to support different signal conditioners and cables.
ABA 173
The ABA 173 industrial housing can contain up to 8 signal conditioners and is available in two versions: a standard version and a version approved for use in potentially explosive atmospheres. Both versions are configurable and can be ordered with various cable fittings (stuffing glands) to support different signal conditioners and cables.
ABE 04x
This rack is used to house hardware from Meggitt's Vibro-Meter VM600 series of machinery protection systems and condition monitoring systems.
AE 119
Housing Expansion Probe type AE 119
AMC 8
The AMC 8 and IOC 8T cards are designed for use in Meggitt's Vibro-Meter VM600 series of machinery protection equipment. The AMC 8 analog monitoring card is installed in the front of the ABE 04X rack. The IOC 8T input/output card is installed in the rear of the rack. Both cards connect directly to the rack’s backplane via two connectors.
The cards provide eight channels of temperature monitoring, accepting both resistance temperature detector (RTD) and thermocouple (TC) temperature inputs, as well as process inputs. The source for each channel can be selected during the configuration of the cards.
APF 195
The APF 195 DC-DC converter is a power supply that is suitable for use in machinery monitoring applications. The APF 195 mounts on a DIN rail and can be used to power any equipment requiring a 24 VDC power supply at up to 0.26 A.
APF 196
The APF 196 AC-DC converter is a power supply that is suitable for use in machinery monitoring applications using VM600 rack-based systems or VibroSmart® DMS module-based systems.
The APF 196 mounts on a DIN rail and can be used to power any equipment requiring a 24 VDC power supply at up to 3 A. Up to five power supplies can be connected in parallel for power supply redundancy or increased output current.
APF 197
The APF 197 AC-DC converter is a power supply that is suitable for use in machinery monitoring applications using VM600 rack-based systems or VibroSmart® DMS module-based systems.
The APF 197 mounts on a DIN rail and can be used to power any equipment requiring a 24 VDC power supply at up to 5A. Up to five power supplies can be connected in parallel for power supply redundancy or increased output current.
APF 198
The APF 198 AC-DC converter is a power supply that is suitable for use in machinery monitoring applications using VM600 rack-based systems or VibroSmart® DMS module-based systems.
The APF 198 mounts on a DIN rail and can be used to power any equipment requiring a 24 VDC power supply at up to 7.5 A. Up to five power supplies can be connected in parallel for power supply redundancy or increased output current.
APF 200
The APF 200 AC-DC converter is a power supply that is suitable for use in machinery monitoring applications using VM600 rack-based systems or VibroSmart® DMS module-based systems. This power supply is certified for use in potentially explosive atmospheres.
The APF 200 mounts on a DIN rail and can be used to power any equipment requiring a 24 VDC supply at up to 3.75A. Up to five power supplies can be connected in parallel for power supply redundancy or increased output current.
APF 201
The APF 201 AC-DC converter is a power supply that is suitable for use in machinery monitoring applications using VM600 rack-based systems or VibroSmart® DMS module-based systems. This power supply is certified for use in potentially explosive atmospheres.
The APF 201 mounts on a DIN rail and can be used to power any equipment requiring a 24 VDC power supply at up to 7.5 A. Up to five power supplies can be connected in parallel for power supply redundancy or increased output current.
ASPS
The ASPS auxiliary sensor power supply is designed for use in Meggitt's Vibro-Meter VM600 series of machinery protection systems and condition and performance monitoring systems. The ASPS power supply works in coexistence with an existing RPS 6U in a VM600 rack.
CA 134
For cryogenic applications and gas turbines. Piezoelectric accelerometer for use over a very wide temperature range.
10 pC/g (500 g)
-253 to 500°C (-423 to 932°F)
0.5 to 6000 Hz
CA 202
For heavy duty gas and steam turbines. Piezoelectric accelerometer for use over an extended temperature range.
100pC/g (400g)
-55 to 260° C (-67 to 500° F)
0.5 to 5000 Hz
CA 280
For heavy duty and aero-derivative gas turbines, gearboxes, compressors and marine applications. Multi-purpose, compact piezoelectric accelerometer for use over an extended temperature range.
100pC/g (500g)
-55 to 260° C (-67 to 500° F)
0.5 to 10,000 Hz
CA 306
For aero-derivative and industrial gas turbines. Piezoelectric accelerometer for use at high temperatures. Similar parts are standard with numerous OEMs.
50pC/g (100g)
-55 to 500° C
5 to 3000 Hz
CA 901
For heavy duty gas turbines. Piezoelectric accelerometer for use at extreme temperatures. Similar parts are standard with numerous OEMs.
10pC/g (500g)
-196 to 700° C (-321 to 1292 °F)
3 to 3700 Hz
CC 308
Power coupling capacitor designed to monitor partial discharge by measuring current in the leads of generators and motors used in power generation systems. As a result of the robust design and the reliability of the devices, it is possible to install the CC 308 extremely close to the windings, thus minimizing attenuation effects and maximizing system sensitivity.
8 kV
80 pF ± 3 pF
0.5 to 500 MHz
−50 to 150° C (−58 to 302° F)
CC 316
Power coupling capacitor designed to monitor partial discharge by measuring current in the leads of generators and motors used in power generation systems. As a result of the robust design and the reliability of the devices, it is possible to install the CC 316 extremely close to the windings, thus minimizing attenuation effects and maximizing system sensitivity.
16 kV
80 pF ± 3 pF
CC 328
Power coupling capacitor designed to monitor partial discharge by measuring current in the leads of generators and motors used in power generation systems. As a result of the robust design and the reliability of the devices, it is possible to install the CC 328 extremely close to the windings, thus minimizing attenuation effects and maximizing system sensitivity.
28 kV
80 pF ± 3 pF
CCM 524
Carrier Card module type CCM 524
CE 134
For heavy duty gas turbines, aero-derivative gas turbines and compressors. Piezoelectric accelerometer with attached electronics, for use over an extended temperature range.
5µA/g (400g)
-55 to 350° C (-67 to 662 °F)
5 to 10,000 Hz
CE 281
For gearboxes, compressors, pumps and fans. Compact piezoelectric accelerometer with attached electronics, for use over an extended temperature range.
10µA/g (200g)
-55 to 260° C (-67 to 500° F)
3 to 10,000 Hz
CE 311
For heavy duty gas and steam turbines. Piezoelectric accelerometer with built-in electronics, for use in industrial environments.
50µA/g (40g)
-55 to 125° C (-67 to 257° F)
2 to 8000 Hz
CE 680
For auxiliary machines. Multi-purpose, compact piezoelectric accelerometer with built-in electronics, for use in industrial environments.
100mV/g (80g)
-55 to 120° C (-67 to 248° F)
0.5 to 9000 Hz
CMC 16
The CMC 16 condition monitoring card is the central element in Meggitt's Vibro-Meter VM600 series condition monitoring system (CMS). This intelligent front-end data acquisition unit (DAU) is used in conjunction with the VM600 CMS software to acquire, analyse and transmit results to a host computer via the VM600 series CPU M module with Ethernet controller or directly via serial links.
CMS software
Condition-based maintenance is a predictive methodology that can be used to improve your asset/machinery effectiveness. Condition monitoring software (CMS) is based on this principle and is dedicated to the support of technicians, operators and engineers, enabling them to rapidly identify a problem, evaluate the situation and determine appropriate action to take.
CP 103
Very high temperature dynamic pressure sensor. Similar parts are standard with numerous OEMs.
232pC/bar (20bar)
Overload up to 250 bar
-196 to 700° C (-321 to 1292° F)
2 to 10,000 Hz
CP 211
Very high temperature, compact dynamic pressure sensor. Mostly used for laboratory measurements in extreme environments.
25pC/bar (250 bar)
Overload up to 350 bar
-196 to 777° C (-321 to 1431° F)
2 to 15,000 Hz
CP 216
High temperature, compact dynamic pressure sensor. Similar parts are standard with numerous OEMs.
200pC/bar (250 bar)
Overload up to 350 bar
-70 to 520° C (-94 to 968° F)
2 to 15,000 Hz
CP 235
High temperature, very high sensitivity dynamic pressure sensor. Similar parts are standard with numerous OEMs.
750pC/bar (20 bar)
Overload up to 100 bar
-55 to 520° C (-67 to 968° F)
2 to 10,000 Hz
CP 502
High temperature dynamic pressure sensor. The GaPO4 (gallium phosphate) piezoelectric material used ensures outstanding thermal behaviour (no pyroelectricity) and virtually constant sensitivity.
Sensitivity ≥ 90 pC / bar
Burst pressure 100 bar (max.)
Operating temperature −70 to 560° C (-94° C to 1040° F)
Frequency range 0.5 to 20,000 Hz
DIC 413
The DIC 413 is a controller designed to match the EW 140 ice sensor. It provides power to and reads the current-modulated signal from the EW 140. The controller then converts this signal into an analog voltage.
EC 175
Threaded connection and armored softline cable.
EC 349
Overbraided softline cable
EC 439
The EC439 is a 2-wire cable assembly for a VE 210 transducer with a current-modulated output signal.
This cable assembly is available with or without a flexible stainless steel hose (protection tube).
EC 440
The EC440 is a 3-wire cable assembly for a VE 210 transducer with a voltage-modulated output signal.
This cable assembly is available with or without a flexible stainless steel hose (protection tube).
EE 139
Bayonet connection and softline cable
EE 143
Threaded connection and softline cable.
EE 152
Cable assembly for TSU 109
EW 140
For all gas turbines. Detects initiation of ice on gas turbine inlets. Used by turbine de-icing systems, to optimize the use of bleed air.
0.2 to 2 mm ice
-55 to 120° C (-67 to 248° F)
GSI 127
The GSI 127 is for use with piezoelectric transducers with integrated electronics, piezoelectric transducer signal conditioners and proximity probe signal conditioners. This brand new product is a drop-in replacement for the GSI 124.
GSI 124
The GSI 124 is for use with piezoelectric transducers with integrated electronics, piezoelectric transducer signal conditioners and proximity probe signal conditioners.
GSV 14x
The GSV 14X series of power supply units is designed to supply transducers and conditioners in potentially explosive atmospheres (hazardou areas).
MPC 4
The MPC 4 machinery protection card is the central element in Meggitt's Vibro-Meter VM600 series machinery protection system. This very versatile card is capable of measuring and monitoring up to 4 dynamic signal inputs and up to 2 speed inputs simultaneously.
MPS software
MPS1 and MPS2 allow stand-alone configuration of MPC 4 and AMC 8 cards, via the cards' serial connectors. Alternatively, if the cards are installed in a networked VM600 rack, i.e. one containing a modular CPU card (type CPU M) used for rack control and communication, they can be configured in "one-shot" mode using an Ethernet TCP/IP link from the PC to the CPU M.
Vibro-Meter Energy markasına ait tüm ürünler
0 kayıt bulundu